VIP member
30 ton 300KN microcomputer controlled electronic testing machine
The testing machine adopts advanced chip integration technology and a PCI data acquisition, amplification, and control system designed by * *. The amp
Product details
Working principle
The computer system of the electronic testing machine controls the servo motor to rotate through a controller and a speed regulation system. After being decelerated by a reduction system, the moving crossbeam is driven up and down by a screw pair to complete various mechanical performance tests such as tensile, compressive, bending, and shearing of the sample.
Machine characteristics
Low noise, high efficiency, with a very wide speed range and beam movement distance, and equipped with a variety of test attachments, it has a very broad application prospect in the mechanical performance testing of metal, non-metal, composite materials and products.
Purpose and Parameters
This machine can test materials such as rubber, plastic, leather, metal, nylon thread, fabric, paper, aviation, packaging, construction, vehicles, etc. It can perform tensile tests, pressure tests, peel tests, tear tests, shear bending tests, etc.
The computer system of the electronic testing machine controls the servo motor to rotate through a controller and a speed regulation system. After being decelerated by a reduction system, the moving crossbeam is driven up and down by a screw pair to complete various mechanical performance tests such as tensile, compressive, bending, and shearing of the sample.
Machine characteristics
Low noise, high efficiency, with a very wide speed range and beam movement distance, and equipped with a variety of test attachments, it has a very broad application prospect in the mechanical performance testing of metal, non-metal, composite materials and products.
Purpose and Parameters
This machine can test materials such as rubber, plastic, leather, metal, nylon thread, fabric, paper, aviation, packaging, construction, vehicles, etc. It can perform tensile tests, pressure tests, peel tests, tear tests, shear bending tests, etc.
Meet standardsGB/T228-2002Method for Tensile Testing of Metallic Materials at Room TemperatureGB/T7314-1987The requirements of the "Metal Compression Test Method" are metGB、ISO、ASTM、DINProcessing data according to various standards. Can meet the requirements of users and provide standards.
**Maintenance of testing machine host
(1) Regularly check the screws at the jaws of the testing machine, and tighten them promptly if they are loose;
(2) The fixtures equipped with the testing machine should be coated with anti rust oil for storage;
(3) The sliding surface in contact with the steel plate and the lining plate, as well as the groove surface on the lining plate, should be kept clean and regularly coated with a thin layer of molybdenum disulfide grease;
(4) Regularly check the transmission condition of the sprocket. If there is any looseness, please re tighten the tensioning wheel;
(5) Due to the frequent use of the jaws of the electronic tensile testing machine, they are prone to wear and tear, and excessive oxidation skin can easily cause damage to the small piston and oil leakage. Therefore, it is recommended to clean them after each test is completed;
2、 Maintenance of the control system of the testing machine
(1) Regularly check whether the connecting wires on the back panel of the testing machine controller are in good contact. If they are loose, they should be tightened in a timely manner;
(2) If the machine is not used for a long period of time after the experiment, turn off the controller and computer of the testing machine;
(3) The interface on the controller of the testing machine corresponds, and plugging in the wrong interface may cause damage to the equipment;
(4) The interface on the plug-in controller must be powered off.
(1) Regularly check the screws at the jaws of the testing machine, and tighten them promptly if they are loose;
(2) The fixtures equipped with the testing machine should be coated with anti rust oil for storage;
(3) The sliding surface in contact with the steel plate and the lining plate, as well as the groove surface on the lining plate, should be kept clean and regularly coated with a thin layer of molybdenum disulfide grease;
(4) Regularly check the transmission condition of the sprocket. If there is any looseness, please re tighten the tensioning wheel;
(5) Due to the frequent use of the jaws of the electronic tensile testing machine, they are prone to wear and tear, and excessive oxidation skin can easily cause damage to the small piston and oil leakage. Therefore, it is recommended to clean them after each test is completed;
2、 Maintenance of the control system of the testing machine
(1) Regularly check whether the connecting wires on the back panel of the testing machine controller are in good contact. If they are loose, they should be tightened in a timely manner;
(2) If the machine is not used for a long period of time after the experiment, turn off the controller and computer of the testing machine;
(3) The interface on the controller of the testing machine corresponds, and plugging in the wrong interface may cause damage to the equipment;
(4) The interface on the plug-in controller must be powered off.
Online inquiry
-
Contacts
-
Company
-
Telephone
-
Email
-
WeChat
-
Verification Code
-
Message Content
-